Root Motorola Moto G30 Android 11 using Magisk
Root Moto G30 Android 10 XT2115
Root Motorola XT2115 Android 10
روت Motorola XT2115 Android 10
روت Motorola Moto G30 XT2115 Android 10
شرح روت Motorola XT2115 Android 10
تحميل روت Motorola XT2115 Android 10
ROOT Motorola Moto G30 XT2115 Android 10
ROOT + TWRP Motorola XT2115 Android 10
How to Root Moto G30 Android 10 version (XT2115, International Variants)?
Moto G30 International Variants comes with a flexible bootloader other than some carrier-locked devices. It means that we can easily root different smartphone variants. The device can also accept installing TWRP recovery or any other custom recovery file/app.
For most of the methods, We follow Magisk to root our device. TWRP recovery is a custom recovery file that we must install on your devices because you can root them successfully. This article explained the easiest method to follow and install Magisk on Moto G30. However, the tool required for rooting this device is the Magisk App.
You can install TWRP Recovery once available for your Moto G30 to gain Custom Recovery access. Before sharing the tutorial, you may want to know that, without the TWRP recovery present on your device, you can not install any custom ROM or firmware. Does it seem complicated? Relax; we will explain everything briefly in bullets.
Things to check out for;
Make sure your device battery is above 50%.
You should back up your current files and data, full data loss process (save them on external storage).
Pre-Requirement Steps
Enable USB Debugging Mode and OEM Unlock on your mobile. To do this, go to settings >>> about >>> Tap on the “Build Number” 7-10 times consistently to enable “Developer Options,” then go to the “Developer Options” and enable USB Debugging Mode, OEM Unlock. There is no complicated process in Moto G30.
Download and install the Moto USB driver to your computer system.
Also, download the ADB drivers. Install it on your PC.
Unlock Moto G30 bootloader using ADB and Fastboot
- Switch off your device. Then, enter into Fastboot mode. To do this- Press and hold down the Volume Down + Power buttons simultaneously for some time.
Press the Volume Up button to continue when you see the warning message.
Now, connect the Moto G30 mobile to the computer via USB cable.
Launch the fastboot on your computer. Open a Command prompt on your PC and type the below command.
- fastboot devices
- It should display the connected devices. If you didn’t get the device, restart the command prompt and Disconnect and Connect your Moto G30; if you are detected, type the below commands.
- fastboot oem get_unlock_data
- Hit enter, you will get some unlock data. Copy those codes and remove < bootloader> Prefix from those lines and copy them into one line.
- Go to Official Moto Unlock Page. Log in with your moto account and in the Box, Paste those codes and Check the unlock Bootloader Status. If you get, Yes, you can unlock; you can request unlock Key from Moto.
After the process completes, you will get 20 Digit to unlock the key in your email. Now type the following command to unlock the bootloader on your device.
- fastboot oem unlock UNIQUE CODE
You should type this code two times and Hit enter to unlock your device successfully. After the successful unlock, your device will automatically reboot to the standard OS.
- Check again to enable “Developer Options,” then go to the “Developer Options” and enable USB Debugging Mode, OEM Unlock. Sometimes they disabled themselves after the boot.
Preparing Patched Boot Image file
- Download Moto G30 Firmware and save it on your PC. Your Current OS version and Downloaded Version should be the Same.
- You can use Phone Info to know your firmware version.
- Download 7Zip-ZS Install on your PC. Extract the files in downloaded firmware using 7Zip-ZS. You will get a lot of data. Copy boot.img file to your mobile.
- Download Magisk Manager (Download Latest version) or Magisk canary and Install it on your mobile. Open Installed Magisk and Select Install in Magisk; ask For a zip file and Patch Recovery Image File. Select the boot image file.
Navigate to your copied boot image File and patch the file in .img format.
- Wait for the process to complete; you will get a magisk patched .img file in the end. The .img file will be in the same folder where you have the boot. img.
- Copy the magisk_patched.img file to your PC. Rename the file to boot.img again.
Flash Patched Boot Image in Moto G30 using ADB and Fastboot
- Switch off your device. Then, enter into fastboot mode. To do this- Press and hold down the Volume Down + Power buttons simultaneously for some time.
Press the Volume Up button to continue when you see the warning message.
Now, connect the Moto G30 mobile to the computer via USB cable.
Launch the fastboot on your computer. Open a Command prompt on your PC and type the below command.
- fastboot devices
- It should display the connected devices. If you didn’t get the device, restart the command prompt and Disconnect and Connect your Moto G30. If you are detected, type the below command and hit Enter.
- fastboot flash boot_a patched_boot.imgfastboot flash boot_b patched_boot.img
- After the process complete, Press the Volume Down+ Power button to exit Fastboot mode. When the screen goes off, Immediately Press Volume Up + Power buttons to boot into Recovery mode.
- After entering into Stock recovery mode, Go to Wipe Data/Factory Reset and Select Yes to wipe data. It will erase your saved data on your device. Don’t Boot into OS; read below Boot stages before booting.
Boot into Rooted OS
- Press and Hold Volume Up + Power buttons, release all the keys once the Bootloader warning appears. You have to set up your device like a new device. You can select the root status using the Root Checker.
- Stock Recovery Boot – Press and Hold Volume Up + Power buttons, release keys while you hold the Volume Up key.
- You will see Magisk Manager in your App drawer. If you can’t find the app, you can install Magisk Manager on your mobile.
ليست هناك تعليقات:
إرسال تعليق